M-Button Motogadget

In stock

49.00
TTC


M-Button Motogadget
 
Another innovation from motogadget: the m-Button.
It's a big help - in combination with the new m-Unit V.2 - in reducing 'cable clutter' and simplifying wiring harnesses.
 
 
Integrated into the handlebar tube - or any other adequate location - this tiny cylinder will electrically connect all handlebar instruments, switches and buttons.
Using state-of-the-art bus technology, the m-Button digitally processes signals and transmits them to the m-Unit V.2 over a thin cable.
The electrical consumers will then be switched inside the m-Unit.
All control wires are moved into the handlebar. This saves space, weight, labour and time. A 'must have' for custom bikes with clean-look handlebars.
 
 
 
In simple facts:
a) normally, the operating current (e.g. headlight or turn signals) is transmitted directly via the wiring of the handlebar switches. Due to the high currents, cables with large cross-sections have to be routed from the fuse box to the switch and back to the electrical consumer. 
The result: big cable bundles. Definitely, a 'no go' for custom bikes with restricted space or a concealed electrical system.
 
b) using the m-Unit without the m-Button, just a thin cable for each switch- or button-controlled feature has to be routed to the m-Unit. These cables only carry minute control currents. All high loads and currents are switched directly at the m-Unit and transmitted directly to the electrical consumers. This already leads to a significant reduction and simplification of the wiring harness. Here you can see the example of a circuit diagram.
 
c) using the m-Unit V.2 in combination with the tiny m-Button, you will once again reduce the amount of cables that have to be routed! All switches/buttons on the handlebar are connected at the shortest distance possible and concealed inside the handlebar. Consequently, you will have to route only ONE thin cable from the m-Button to the m-Unit. All loads and currents will be switched directly at the m-Unit V.2 (see explanations above). A layout reduced to the max! Here you can see the example of a circuit diagram with use of m-Button.
 
 
The m-Button is completely moulded in, making it water-tight and resistant to vibrations.
 
The m-Button is equipped with connections for
- turn signal, left side
- turn signal, right side
- headlight (low beam and high beam)
- E-starter
- horn
- brake light switch, front brake
 
m-Button – dimensions
Diameter: 12 mm
Length: 25 mm
Cable length: approx. 60 cm
Connecting cable to m-Unit: approx. 200 cm
Weight: approx. 30 g
 
Attention: The only intended use of the m-Button is in combination with m-Unit V.2.

We also recommend


Customers who bought this product also bought


Browse these categories as well: ELECTRICITY - for Triumph Hinckley Bonneville, Scrambler, Thruxton et Café Racer, MOTOGADGET motorcycle parts for Triumph Hinckley Bonneville, Scrambler, Thruxton and Café Racer, PARTS NEW BONNEVILLE T120 - for New Triumph Hinckley Bonneville, Scrambler, Thruxton 2016, ACCESSOIRES NEW THRUXTON 120 - for New Triumph Hinckley Bonneville, Scrambler, Thruxton 2016, PARTS SPEED TWIN 1200, PARTS STREET SCRAMBLER for new Triumph Hinckley Bonneville, Scrambler, Thruxton 2016, PARTS STREET TWIN - for new Triumph Hinckley Bonneville, Scrambler, Thruxton 2016, ACCESSOIRES NEW THRUXTON 1200 R - for New Triumph Hinckley Bonneville, Scrambler, Thruxton 2016, PARTS BOBBER 1200 - for new Triumph Hinckley Bonneville Bobber 2017, BONNEVILLE EFI / INJECTION ACCESSORIES UNTIL 2015, TRIUMPH BONNEVILLE CARBS ACCESSORIES 2001-2007, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES, ACCESSOIRES